Skip to content

PT Hookah Coals Coconut Charcoal Indonesia · Mungkid, Magelang, Central Java, Indonesia

Menu

Desk

Quality Control Desk — What Is Checked and What You Can Ask For

This is the quality control desk of the hookah coals factory in Magelang, for buyers of shisha charcoal by the container. The page pairs each check with the proof a buyer can ask for.

Written by
Rudi Kurniawan
Updated
The size of a cube hookah coal is its edge length in millimeters, read with a caliper.

Quality control desk

Desk leadSri WahyuniQuality Control Supervisor

What to send

  • Your target ranges and tolerances
  • How the coals will be used: lounge, retail or both
  • For a quality question: photos, your measurements and the order reference

What comes back

  • The specification sheet with target ranges
  • A sample to test
  • The lab report for the batch, on request

The sheet for this desk Specification sheet

Quick answer

What does the factory check, and what proof can I ask for?

Quality control is run by Sri Wahyuni, Quality Control Supervisor. For each order a buyer can ask for three things: the specification sheet with target ranges, a sample to test, and the lab report for the batch. Each control point on this page is paired with what a buyer can ask to see.

1. Who runs quality control

The desk is run by Sri Wahyuni, Quality Control Supervisor. It handles three things for a buyer: the specification before production, questions about a sample, and questions about a delivered batch.

Definition

quality control

Quality control is the set of checks a factory makes on material and product at fixed points of production, from raw material to packed carton.

Note

Quality control answers with numbers. A question that arrives with a measurement and an order reference can be compared with the specification; a general remark cannot.

2. Control points from raw material to carton

A briquette is checked where a fault can still be caught. The table gives the four points and, for each, what a buyer can ask to see.

Four control points in hookah coal production, what is checked at each and what a buyer can ask to see. General control points for the product; the factory's own checks replace these rows when it states them.
Control pointWhat is checkedWhat a buyer can ask to see
Raw material The shell charcoal before it is groundA photo of the material as received
Pressing Shape, size and pieces per kilogramA caliper reading and a count of one kilogram
Drying Moisture after the ovensThe moisture value on the lab report
Packing Weight and count per inner unit, carton marksA photo of an open carton and of its marks
The count per kilogram is found by weighing out one kilogram of hookah coals of one shape and size and counting the pieces.

Which station decides which property is on the page about how hookah coals are made.

3. What the quality control desk needs from you

The desk can only check against what you asked for. Three things have to be stated before production:

  • your target ranges: ash, moisture, burn time and breakage, each with its method;
  • your tolerance on size and on pieces per kilogram;
  • how the coals will be used, because a lounge and a retail brand weigh the numbers differently.

Important

If a claim arises later, send photos, your own measurements and the order reference. Without them the desk has nothing to compare.

4. What you receive for each order

Three proofs go with an order, and each answers a different question.

  • The specification sheet says what was ordered, in numbers.
  • A sample shows what the factory can make, before you order.
  • The lab report shows what a named sample measured. It is sent on request.

Which documents exist today, and which are still requested from the factory, is on the page of documents and their status.

5. Sheets and pages for quality questions

The desk works from three sheets and one guide.

Tip

Use them in that order. A specification written before the sample arrives gives the test something to be measured against.

Questions and answers

What proof of quality can I ask for with an order?
Three things: the specification sheet with target ranges, a sample to test before you order, and the lab report for the batch, sent on request.
Who is responsible for quality control at the factory?
Sri Wahyuni, Quality Control Supervisor, runs the quality control desk.

Write your limits on the specification sheet

State the values you need. Quality control answers which grade is offered against them.

Open the specification sheet