Skip to content

PT Hookah Coals Coconut Charcoal Indonesia · Mungkid, Magelang, Central Java, Indonesia · [email protected]

Menu

Guide · Quality Control

Hookah Coal Troubleshooting — Symptom, Cause, What to Send

This page belongs to the quality control desk of the factory, which makes hookah coals, also called shisha charcoal. It is for a buyer whose coals show a fault: it names what could cause it and what to send so that it can be checked.

Written by
Rudi Kurniawan
Published
Updated
Broken cubes of hookah coals are set beside whole ones from the same batch, so that a fault can be described by what is seen.

Quick answer

My coals show a fault: what could cause it, and what do I send so it can be checked?

A fault in hookah coals has several possible causes, in production, in transport or in use; the triage table lists them by symptom. Each row ends with what the quality control desk needs to see, and a cause is confirmed only against the batch. Find your symptom, gather what its row asks for, and send it with the carton marks, so that the report can be tied to one batch.

1. Triage table: symptom, possible causes, what to send

Find the symptom in the first column. The two middle columns list what could cause it, on the factory's side and after the container left; the last column is what to send.

Definition

coal fault

A coal fault is a defect that can be observed in a hookah coal, such as a crack, breakage, a smell on warming up, heavy ash, a short burn or uneven size.

Seven symptoms a buyer can observe in hookah coals, each with possible causes in production, possible causes in transport or use, and what to send to the factory's quality control desk so that the cause can be checked against the batch.
SymptomPossible causes in productionPossible causes in transport or useWhat to send
Cracks or broken pieces Pressing or drying of the batchDrops, crushed cartons or damp on the way; how the coals were heatedPhotos of the pieces and of the carton they came from; the number of cartons affected
Smell or smoke on warming up The raw material or the drying of the batchDamp taken up in storage; residue on the heaterA short video of pieces warming up on a clean electric coil; how the cartons were stored
More ash than expected The ash of the batch against the grade orderedA comparison by eye with another product or another setupA photo of the ash from a counted number of pieces; the grade on your order
Short burn The density or the size of the piecesA heat source or setup that differs from the one the sample was tested onThe burn time of three pieces on one heat source; the measured size of the pieces
Slow to light The density or the moisture of the batchDamp taken up in storage; a weaker heat sourceThe time to light on one heat source; how the cartons were stored
Uneven size or weight The mold or the cutting of the batch—Caliper readings of ten pieces from three cartons; the count of pieces in one kilogram
Damp or soft cartons —Condensation or water in the containerPhotos at the open doors before unloading; the seal number; where the cartons stood

Caution

Every cause in the table is a possibility. Which one applies to your coals is known only after the report has been checked against the batch.

2. Before you report a fault

A report that can be checked needs no second round of questions. Four steps make it checkable.

  1. Test on one heat source

    Use the same heat source for every piece you test, and say which one it was. The factory's own burn test is run like this: three pieces are lit on an electric coil, and the time to light and the burn time are recorded.

  2. Compare with your reference sample

    Test pieces from the sealed sample of the run you approved beside pieces from the container, on the same day and in the same way.

  3. Note the carton marks

    Write down the marks and the production date on every carton the pieces came from. They tie your report to one batch.

  4. Count what is affected

    Open cartons from the front, the middle and the back of the load, and give the number of cartons checked and the number with the fault.

The size of a cube hookah coal is its edge length in millimeters, read with a caliper.

The same tests, with the same record, are on the sample test sheet. The figures to measure against are the ones you wrote on the specification sheet before the order.

3. What the factory checks on its side

The factory checks a report against its own record of the batch and against the sample it kept.

  • The factory fails a batch on smell or smoke on warming up.
  • The factory fails a batch on high ash.
  • The factory fails a batch on cracks or breakage.
  • The factory fails a batch on uneven size or density.

The factory keeps a sample of about 25 kg from every batch for 5 years. Pieces from that sample can be tested beside the ones you report. Its drop test is run like this: lit pieces are dropped onto a hard tiled floor, from 100 cm for cubes and from 30 cm for hexagonal, dome and finger shapes.

A retained sample of a batch of hookah coals lets a later report from a buyer be checked against the coals that were shipped.

The desk is run by Sri Wahyuni, Quality Control Supervisor. A fault that shows in the retained sample points to the batch. A fault that does not show there points to what happened after loading, and the report is read again with that in mind. How two runs are kept alike is on the page about consistency between orders.

Note

The table and the checks say where to look. They do not say in advance whose fault a problem is.

4. Report it: arrival sheet or claim form

Two sheets carry a report, and which one to use depends on when the fault shows.

  • A container that has just arrived: fill in the arrival sheet while it is unloaded. It records the seal, the carton count and a measured sample of cartons.
  • A fault you want the factory to answer for: send the claim form on the page about complaints and claims, with the evidence the table asks for.

A claim has a time limit. The factory accepts a claim on quantity within one week and on quality within two weeks of the container's arrival at the buyer's warehouse. Report a fault as soon as it shows, even if you have not finished the tests.

Tip

Keep the cartons the faulty pieces came from, closed and dry, until the report has been answered.

Questions and answers

Why do hookah coals crack or break?
Possible causes lie in production (pressing and drying), in transport (drops, crushed cartons, damp) and in use (how the coals are heated). The cause for your coals is confirmed only against the batch, so send photos of the pieces, the carton marks and the production date.
What should I send when coals from a container show a fault?
Photos or a short video of the fault, the carton marks and the production date, the number of cartons affected, and how the coals were stored and lit. For a container that has just arrived use the arrival sheet; for a claim use the claim form.
Does a smell when lighting mean the coals are faulty?
Not by itself. The factory fails a batch on smell or smoke on warming up, so the retained sample of your batch can be checked against your report. First test on one heat source and compare with your reference sample.

Write your limits on the specification sheet

State the values you need. Quality control answers which grade is offered against them.

Open the specification sheet