Skip to content

PT Hookah Coals Coconut Charcoal Indonesia · Mungkid, Magelang, Central Java, Indonesia

Menu

Order sheet · Quality Control

Sample Test Sheet — Score Hookah Coal Samples in One Session

This sheet belongs to the quality control desk of the factory, which makes hookah coals, also called shisha charcoal. It is a scorecard for one session: fill it in as you test, print it, or send your scores back to the desk.

Written by
Rudi Kurniawan
Updated

Quick answer

How do I test a sample so the result means something?

Test a hookah coal sample the way it will be used, on one heat source, and write every result down. Count and weigh the pieces, measure three of them, time ignition and burn, look at the ash, and note smell and broken pieces. Then compare each result with the specification sheet. A sample test judged from memory proves nothing.

1. What you need for the test

Four tools are enough: a scale, calipers, one heat source and a timer. Use the heat source your customers use, and use the same one for every sample you compare.

Definition

sample test

A sample test is the set of checks a buyer runs on a sample parcel and records for comparison with the specification sheet.

Note

These steps are general practice for testing hookah coals. They are not a protocol of this factory, and they do not replace a lab report.

If you have no samples yet, ask for them by shape and grade on the sample request sheet.

2. The scorecard

Seven checks, each with what to do, what to write down and what to compare it with.

The sample test scorecard for hookah coals: seven checks, how to do each, what to record and what to compare the result with.
CheckHow to do itWhat to recordCompare with
Count and weight Count the pieces in the pack and weigh them togetherPieces and gramsPieces per kilogram on the specification
Size Measure three pieces with calipers, on each edgeMillimeters for each pieceSize and tolerance on the specification
Ignition Heat one piece on your heat source and time it until it is fully litMinutesYour current coals on the same heat source
Burn time Leave the lit piece on your usual setup and time itMinutes, with the setup namedBurn time on the specification
Ash Look at the ash when the piece has burned outColor and amount, in your wordsThe ash range of the grade
Smell Note any smell while the piece lightsYes or no, and what kindYour current coals
Broken pieces Count broken pieces before you handle the packNumber of piecesThe breakage limit on the specification

Tip

Test two grades side by side in the same session. A difference between two samples is easier to see than a difference from a number.

3. Reading the result

Each score falls into one of three groups, and each group has one next step.

  • Within the target: the sample matches. Write that range into your specification.
  • Close to the edge: ask the quality control desk. Send the score and how you measured it.
  • Outside the target: say so before you order. Ask for another grade or state the range you need.

The targets are on the specification sheet, and the ranges of each grade on the page of the grades in numbers.

Caution

Burn time and ignition depend on the heat source and the setup. Compare a sample with your current coals on the same setup, not with a number measured elsewhere.

4. What a sample cannot tell you

A sample is one parcel. It cannot tell you whether the tenth container will match the first.

That is what the signed specification is for: it fixes the ranges every container has to meet. What a lab report adds, and how to check one, is on the page about lab reports and how to verify them.

Important

Keep part of the sample you approve. It is the reference you hold the first container against.

5. Send your scores

Send your scores to the quality control desk. A score outside the target gets an answer on what can be changed.

  1. Why we ask: A quote, a parcel and every document are addressed to a company.

  2. Why we ask: The reply is sent to this address.

  3. Why we ask: Scores are compared with the targets of that shape and grade.

  4. Why we ask: Ignition and burn times mean something only for one stated heat source.

  5. Why we ask: This gives your own pieces per kilogram.

  6. Why we ask: Three pieces show the spread, not one lucky piece.

  7. Why we ask: Timed from the start of heating to a fully lit piece.

  8. Why we ask: Timed on the same setup for every sample you compare.

  9. Why we ask: Color and amount, in your own words.

  10. Why we ask: Note it while the piece lights, not after.

  11. Why we ask: Count them before you handle the sample.

  12. Why we ask: Details that do not fit a field above.

The reply comes by email to the address you enter.

Questions and answers

How do I test shisha charcoal samples?
Count and weigh the pieces, measure three of them, time ignition and burn on one heat source, look at the ash, and note smell and broken pieces. Write every result down and compare it with the specification sheet.
What tools do I need to test hookah coals?
A scale, calipers, one heat source and a timer.

Write your limits on the specification sheet

State the values you need. Quality control answers which grade is offered against them.

Open the specification sheet