Skip to content

PT Hookah Coals Coconut Charcoal Indonesia · Mungkid, Magelang, Central Java, Indonesia · [email protected]

Menu

Order sheet · Quality Control

Incoming Container Check for Hookah Coals — Arrival Sheet

This sheet belongs to the quality control desk of the factory, which makes hookah coals, also called shisha charcoal. It is the buyer's half of quality control: the check at your warehouse door.

Written by
Rudi Kurniawan
Updated

Quick answer

What do I check when the container arrives, and what do I send if something is off?

Check an arriving container of hookah coals in four steps: seal, carton count and marks, a measured sample, and photos. Write the result on the arrival sheet on this page and send it to the quality control desk. The same sheet, filled in for every container, lets you compare a reorder with the first delivery, and it is the record a claim is checked against.

1. Before you open the container

The first four steps take place before a single carton is moved. They cost a few minutes, and they cannot be repeated later.

Definition

arrival check

An arrival check is the inspection a buyer makes when a container is opened at destination: seal, carton count, marks and a measured sample of cartons.

  1. Read the container number

    Compare the number on the door with the bill of lading and the packing list. Photograph it.

  2. Read the seal

    Compare the seal number with the one on the papers, and check that the seal is intact. Photograph it before it is cut.

  3. Photograph the load as the doors open

    Take the picture before a carton is moved. It shows how the cartons stood, and the gap under the roof.

  4. Photograph any damaged or wet carton

    Take it where it stands, with its marks readable, before it is moved.

Important

A record made on the day is evidence. A description written a week later is a memory.

2. Count the cartons and read the marks

Count the cartons as they come out, and compare the count with the packing list. A difference in count is a question of quantity, and it has to be raised while the container is still on your floor.

Then read the marks on the side of a carton: the product, the size, the grade, the net weight and the batch or production date. They should say what your order says. The papers they are compared with are in the table of export documents.

Note

Write the marks down as they are printed. The batch on the carton is how the factory finds the production run you received.

3. Open and measure a sample of cartons

Do not judge a container by the cartons at the doors. Take cartons from three places, and measure the same things in each.

  • Where: the front, the middle and the back of the container.
  • Count and weight: the pieces in one inner unit, and its weight.
  • Size: three pieces with a caliper, on each edge; the factory states a tolerance of ±0.3 mm per side.
  • Broken pieces: how many, in each carton you open.

Compare each figure with the line of your order on the specification sheet. If you also burn a few pieces, score them the way you scored the sample, on the sample test sheet.

Caution

This page sets no acceptance limit. The limits are the numbers you and the factory signed before production.

4. Repeat the check on every reorder

One arrival check says how one container was. The same check on every container says whether the product is holding steady, which is the subject of the page about consistency between orders.

The factory holds its own half of the comparison: it keeps a sample of about 25 kg from every batch for 5 years.

If the check shows a difference, time matters. The factory states a claim on quantity within one week and on quality within two weeks of the container's arrival at the buyer's warehouse. How to report it is on the page about complaints and claims.

5. Arrival sheet

Fill in the sheet on the day the container is opened. It goes to the quality control desk, run by Sri Wahyuni, Quality Control Supervisor. The form carries text only; send the photos by email to [email protected] with the same order reference.

  1. Why we ask: A quote, a parcel and every document are addressed to a company.

  2. Why we ask: The reply is sent to this address.

  3. Why we ask: The record is filed with the order it belongs to.

  4. Why we ask: It ties the record to one container and to the bill of lading.

  5. Why we ask: The seal shows whether the doors were opened on the way.

  6. Why we ask: The date places the record in the order's timeline.

  7. Why we ask: A difference in count is reported while the container is still on your floor.

  8. Why we ask: The marks name the product, size, grade and batch you received.

  9. Why we ask: Front, middle and back show more than the cartons at the doors.

  10. Why we ask: Size, pieces per kilogram and broken pieces, beside the numbers on your specification.

  11. Why we ask: Say what the photos show, so they can be matched to this record.

The reply comes by email to the address you enter.

Questions and answers

Which cartons should I open when a container arrives?
Take cartons from the front, the middle and the back of the container, not only from the doors. Measure the same things in each and write the results on the arrival sheet.
What should I photograph before unloading?
The seal with its number, the container number, the cartons as they stand when the doors open, and any damaged or wet carton before it is moved.

Write your limits on the specification sheet

State the values you need. Quality control answers which grade is offered against them.

Open the specification sheet